The Emitter is connected to the Negative of the Battery, the Collector is connected to the Main Coil, and the Base is connected to the part of the circuit that tells the transistor when to turn ON and when to turn OFF. The Resistor is a passive component that regulates how much electric current moves through that part of the circuit. It has two connections fitted to either end of a cylindrical body. It can be hooked up to the circuit in either direction. It acts like a valve that is open to electricity flowing in one direction, but if it tries to go backwards, the valve shuts and prevents the electricity from coming back.
The Capacitor is a component that stores electricity. Whereas a battery stores electricity in a chemical form, the capacitor stores the electricity as an electrical stress across a material called the "dielectric. Actually, most semi-conductor junctions produce some light when they operate, but LEDs are designed to maximize the light producing function.
The Neon Light is a specialty lighting device where two electrodes are placed near each other in an enclosed space that contains a small amount of Neon gas at very low pressure. It usually takes about volts to make a neon bulb light up. The Switch is any device that allows a temporary contact between two sections of a circuit. In the Bedini SG Project, the Switch is used to discharge the Capacitor into the Battery after it has been charged to a certain level by the discharges of the Main Coil.
The Wheel is made from a bicycle wheel rim. The exact dimension of the wheel rim is 22 inches, measuring from the outside of the rim on one side to the outside of the rim on the other side. The Coil consists of 8 strands of wire that are each feet long 7 strands of 20 wire and 1 strand of 23 wire. The next operation involves filling the core of the spool with the iron "welding rod" sections.
We used aroud of them. Our project finds in application in the remote areas where electricity is not available. It can also be tremendiously useful in military applications to provide electricity in remote adverse areas. It provides free of cost energy. A larger unit developed can be used as an independent grid. At a time where there is growing importance of energy conservation and the depeleting energy resources.
Development of free energy devices would serve as a much easier and better alternative to the depeleting resources. Like to share?
Related Pulse-Charging Battery Systems Newer Post Older Post Home item. Hot in week. Tesla Bifilar Coil Magnet Generator. Overview of Tesla's Bifilar coil and magnet generator According to textbooks, technical books of mainstream science, when it comes to m A brief description of the Bifilar coil Bifilar coil is made up of 2 metal wires that are conductive, with each wire wound in a spiral form Radiant energy receivers with emitters available in nature - the sky 1.
Understand how radiant energy capture mechanism works To build Radio Shack has a wide range of resistors and potentiometers. Tape can be used in some placed. Tolerances Any tape that is adequately sticky and non-magnetic Quantity Enough for the circumference of your wheel plus a little for overlap and do-over.
Sourcing Most any store. Get the exact component called. Quantity One for the circuit and several extra in case you burn one up Sourcing See Digikey. Last resort, try lumber yard or hardware store. Direction of rotation does not have to be perpendicular to coil, but can be at 90 degrees as well. The Earth's North Pole is magnetically south, so the "north" end of your compass will be attracted to the "south" end of your magnet.
Determine an equal spacing for the magnets about the perimeter of the wheel and mark where they should go. This is not crucial to proper operation with one coil, but if you want to later add more coils each with a separate circuit , symmetrical spacing will be important for symmetrical firing.
If you wish to use more than one coil, each coil will need its own complete circuit. All coils will need to fire in unison, so the magnet spacing will need to be uniform.
Arrangement of the winding is not crucial. There is no pattern required. Symmetry is not required. The window of tolerance is very wide here. You might use a drill to spin the spool. John says the exact number of turns on the coil is not crucial. Close is adequate. The window of tolerance is quite wide here.
Keep track of input output pairs. Tips Counting visually is nerve-wracking and prone to error. Use an audible trigger in winding e. This will hit your hand as the spool turns, helping you to count turns. Tap the last few rods in with some light object until you can't fit any more. Make sure the circuit works before soldering the connections. Sterling's suggestion John keeps the wires in his circuit as short as possible, going nearly to the quick when fastening his diodes to the transistor.
Also, be sure to use a heavy guage wire when connecting your batteries in parallel or series. Be sure you understand the risks and that you take necessary precautions. If the neon bulb is not in place, the transistor is likely to burn out if the device is run without a receptacle for the radiant energy e.
The neon bulb absorbs the excess output energy and serves similar to a shock absorber or fuse though nothing is "tripped" and has to be reset. Turning the energizer ON 2. Tuning the energizer 3. Charging a battery with the energizer 4. Evaluating the energizer performance for unity only meaning charging an empty battery from a fully charge battery.
It will then accellerate or decelerate to a point of equilibrium. At some resistances in the circuit, there is more than one stable rate of rotation. It is important that motor operation is sustainable at these values.
Let the machine run until the input battery reaches the manufacturer specified minimum discharge voltage. Measure the output battery capacity by fully discharging it to minimum voltage into a known load. Compare the output battery capacity to that of the input battery. Use a heavy guage wire and terminal connectors with crimping. The above photo shows a set-up for rotation of batteries from the back end to the front, allowing for single battery charging fresh from the front while that battery comes up the same voltage as the bank of batteries, so they can then be connected in parallel.
Adjusting Resistance Note that the arrangement includes a switch to enable meter readings without extended disconnection of the circuit. All of these features, produced at extra cost and time, created the intended effect. No one questioned the explanations of the operation of the machine at the Conference. Significant Mechanical Up-grades The SG Kits came with a bicycle wheel and shaft extensions that when combined, were never able to produce a wheel that ran true. This required major surgery.
The frame bearings and internal wheel bearings and shaft were all abandoned and replaced with a new, larger diameter solid shaft. With these materials installed, the hub of the wheel ran true. The next problem was the rim. With the hub running true, it was obvious how "out of round" the rim was. This required a laborious process of loosening and tighteni. Home Documents 3. Bedini SG the complete advance. If you can't read please download the document. Post on Dec views.
Category: Documents download. Tags: introduction page bedini sg energizer generator mode chapter new chapter conclusion appendices watson machine chapter gfield generator chapter series of bedini sg. This process involves: 1.
Peter Lindemann, D. They include: 1. The frame bearings and internal wheel bearings and shaft were all abandoned and replaced with a new, larger diameter solid shaft www. Spin Connec Resonan in Bedini Machine. Bedini window motor tutorial.
0コメント